| Subject | : | Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 07 Apr, 2007 on 14:32 |
| I am trying to install OS/2 Warp 4.0 on a Gigabyte 965P-DS4 mother board with the following setup: Ide 0 Master (SATA) HDD: Seagate 320GB. Ide 0 Slave (SATA) Nec DVD burner Ide 1 Master (SATA) HDD: Seagate 320GB. I use the danidasd.dmd 1.44 Attached find the config.sys I used to install. |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Pete losepete@ntlworld.com |
| Date | : | 07 Apr, 2007 on 15:33 |
If "Yes" try changing the burner to be the Master on IDE 1 and the disk the Slave on IDE 0 The Danis506 has been updated to 1.7.10 - I do not know if it will help but it is worth a try. Regards Pete |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Fahrvenugen |
| Date | : | 07 Apr, 2007 on 20:33 |
| Hi, Looking over your config.sys file, a few things... If you don't have hardware that requires any of the following, then REM it all out. These can cause difficulty on some systems: basedev=btscsi.add Second, try unplugging one of your 2 hard disks, at least for the purpose of the Warp installation. Once Warp is up and running then go ahead and plug the second Seagate back in. Third, what system kernel are you using on the installation disks? I'd suggest the 14.103a. Good luck! |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | El Vato |
| Date | : | 08 Apr, 2007 on 07:53 |
[...] The newer kernel image may be too big for the classic floppy installation method (the BUNDLE fie on diskette 0 takes considerable space) --unless, of course, he uses 2.88 floppy images burned to an bootable CD-media to bootstrap his OS/2 installation. Best |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | kadzsol |
| Date | : | 08 Apr, 2007 on 09:41 |
Bundle is not the problem (you can delete it for booting up and put it back when installation asks again for floppy 0). The problem is that the new kernel needs at least fixpack 13 files around it, so you also have to update every other dll, exe, etc on (all) the floppies you are using to install. What might also help is removing the second HD (and every other piece of hardware not needed for installation) as advised above and/or creating a FAT partition on your 1st HD with an other OS before booting with OS/2. You may also want to replace IBMATAPI.FLT with Daniatapi.flt. Also make sure you DO use the UNCOMPRESSED version of the DANI Ddrivers. |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 08 Apr, 2007 on 22:53 |
The Disks I use are SATA disks, the burner is a NEC AD 7170S, which also is an SATA burner. Regards, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 08 Apr, 2007 on 22:58 |
As mentioned in a reaction on the first post I removed all disks except 1 HDD and the burner, remmed out all of the above devices but still got the same reaction. I use the kernel that is supplied on the disks of the standard OS/2 installation disks. How do I get kernel 14.103a on it? Best regards, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 08 Apr, 2007 on 23:02 |
I allready replaced the IBMATAPI.FLT by the daniatapi.flt, I also used the uncompressed version of the DANI drivers, still got the same reaction after bootup with only one HDD (Seagate 320GB) Master at 0 and one DVD burner (NEC AD7170S) slave at 0. Best regards, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 08 Apr, 2007 on 23:19 |
I allready found the 1.7.10 version on hobbes, installed it but still got the same reaction, floppy disk led blinks all the time as soon as the 1s506 driver is loaded. Regards, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | El Vato |
| Date | : | 09 Apr, 2007 on 00:14 |
Since you have an OS/2 already performing well, why do not you use Kadzsol's utility (< http://xenia.sote.hu/~kadzsol/rexx/sajat/updcd.htm >)to make an updated current bootable CD-media? As long as you follow the instructions to make an appropriate file structure that includes fixpaks, your choice of kernel, java, etc., UpdCD will take care of updating an original image of your OS/2 Warp 4. Yes, it will take a few trials and will require that you become familiar with Kadzsol's UpdCD framework but you will be surprised at the outcome. You also have the option of using either Daniela's and or IBM's system drivers to attempt your installation --sometimes the IBM drivers succeed over Daniela's and vice-versa. In the past, these are the files that I have replaced to install OS/2 Warp 4 from floppy: os2cdrom.dmd Although IBM deprecated the last of those above in favour of ibmatapi.flt (which in your diskette 1 CONFIG.SYS you must add as: basedev=ibmatapi.flt ) the oldie OS/2 installation apparently still requieres: basedev=ibmatapi.flt Assuming that you are using backup diskette images of your original OS/2 Warp diskette set (always save the original set and work with copies of those, needless to say), you may copy those files listed above from your existing OS/2 installation making room for them by deleting unneeded files existing in your image of oldie diskettes and REMing out those from your diskette 1 CONFIG.SYS Best of luck |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | kadzsol |
| Date | : | 09 Apr, 2007 on 09:56 |
Delete all the partitions from the disk and start installation with a clean disk or with a single FAT16 partition on it. (XP's NTFS partition is seen as HPFS by the OS/2 installer!) Forget the kernel update, it will not help (see my previous post). |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 09 Apr, 2007 on 12:49 |
I put in an empty 80GB Seagate disk and removed all other disks except the burner which I use for the installation, I still get the same reaction. |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | kadzsol |
| Date | : | 09 Apr, 2007 on 13:06 |
try to put a formatted fat16 partition on it |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 09 Apr, 2007 on 13:37 |
I will try this, however this will take some time, I will post a message as soon as I have results. Thanks a lot, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | The Warper |
| Date | : | 09 Apr, 2007 on 15:00 |
| Maybe you just need an updated LVM environment. Or some kind of ACPI support. |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 09 Apr, 2007 on 23:25 |
I now went back to the original installation diskettes by generating them from the Warp 4.0 CD. I thought this over because I tried to bootup a PC that already contained a running ECS installation, with the disks I had. This also resulted in the led blinking on the floppy drive. After that I created the original disks, I only replaced the ibm1s506.add by the danis506.add and could boot up now after remming out the device=testcfg.sys in config.sys, I could look at the HPFS partition of the second drive that held an earlier install of ECS, hopefully I can do the complete install now. Thank you all for the support! Best regards, Jan |
| Subject | : | Re:Installation OS/2 Warp 4 fails |
| Author | : | Jan jan.van.dijk@asm.com |
| Date | : | 10 Apr, 2007 on 16:24 |
| I could do the install until the installation program of Warp 4.0 started after first reboot, now it asked for the testcfg.sys driver to be installed, however if I install this driver in config.sys I get a trap error. I have looked around on the internet and found out that many people have trouble with this driver during installation. It seems this driver has problems with the latest hardware. Is there any one who knows how to overcome the problem with this driver? I have tried to install warp 4.0 on an other PC that already runned warp 4.0, however this PC also trapped on the testcfg.sys. Any tips regarding this testcfg.sys driver issue will be appreciated. I could reanimate the Ecomstation installation I copied from an existing PC. I am now running Ecomstation with the latest danidasd.dmd and danis506.add driver, I simply remmed out the OS2LVM.DMD driver and booted up from this partition and could run all installed programs. All operating systems are running fine now. So I have overcome the testcfg.sys issue. Best regards and thank you all for the great support,
|