| Subject | : | eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 13 Feb, 2007 on 22:52 |
| Hi I'm trying to install eCs 1.2 on my HP laptop with a 60 GB SATA harddisk. At first eCs could not see the harddisk but after I created a boot update disk with the latest Danis506 driver, it is seen and can be partitioned. I have installed bootmanager, and created a bootable logical partition of 1 GB. The installation runs phase 1 without any problems. At the reboot I get the following error from BootManager : The partition is not formatted. If I reboot from the CD, and exit to a commandline, I can change to the C drive, and it contains all the files and directories I would expect, even the new Danis506 ! Any ideas ? Please help ! Kim Foder |
| Subject | : | Re:eCs installation problems |
| Author | : | tex |
| Date | : | 14 Feb, 2007 on 05:36 |
| Is this eCS 1.2 or eCS 1.2MR? |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 14 Feb, 2007 on 08:53 |
| Hi Tex Sorry, it's eCs 1.2R (or Media refresh). |
| Subject | : | Re:eCs installation problems |
| Author | : | dljone9 dljone9@os2world.com |
| Date | : | 14 Feb, 2007 on 10:58 |
You do set that d: partition as "installable" via LVM, correct?? You might try dropping down to a command line first, then doing a |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 14 Feb, 2007 on 19:49 |
| Hi No, I cannot select "make installable" in the lvm menu, mo matter what size i select from 200 mb to 8 gb ! I can select "make startable" and the installation accepts this for the installation drive. The partition is selectable in the boot manager, but (as said) cannot start. |
| Subject | : | Re:eCs installation problems |
| Author | : | dljone9 dljone9@os2world.com |
| Date | : | 14 Feb, 2007 on 21:08 |
| Have you previous experience w/ LVM? You are creating a partition, assigning it the D: drive letter, creating a Volume, then proceeding?? |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 14 Feb, 2007 on 21:58 |
| No previous experiences with lvm. Creating partition assigning letter C: and proceding |
| Subject | : | Re:eCs installation problems |
| Author | : | dljone9 dljone9@os2world.com |
| Date | : | 14 Feb, 2007 on 23:03 |
That might be it, then - creating the volume...an extra step that |
| Subject | : | Re:eCs installation problems |
| Author | : | El Vato |
| Date | : | 15 Feb, 2007 on 04:06 |
Like in the "old" days, if you are creating a boot update diskette set (i.e., Diskette0, diskette1, and diskette2) to install your OS/2 (aka eCS), you need to add the following line prior to the last line of your CONFIG.SYS in your diskette1: SET COPYFROMFLOPPY=1 (make sure to use a text editor to save your changes and NOT a word processor) that statement ensures that ANY driver that you add to the floppy diskette1 and/or diskettte2 (your Danis506 driver, for instance) overwrites that of your CDROM media (that according to you, does not "see" your hard disk). Additionally, I am assuming that you are using an initial 3 diskette installation set and proceed from your CDROM device afterwards. If I am wrong, please read on for a procedure on replacing your CDROM media IBM1S506.ADD witha that of DANIS506.ADD at the end of the first installation phase BUT prior to rebooting your machine.
...and the utility is correct because the driver that did not "see" the 60GB hard disk is active --not the Danis506 that you used to partition your hard disk. As an alternative to the above floppy diskette1 CONFIG.SYS modification, at the end of your phase one installation, press F3 to go into an OS/2 command prompt. Locate your IBM1S506.ADD device driver. Insert your floppy with your Danis506.add equivalent and COPY OVER the IBM1S506.ADD driver. As a specific example, assuming that your IBM1S506.ADD is located in your directory X:\OS2\BOOT (or X:\ECS\BOOT) and X represents your actual OS/2 installation drive, i.e., drive C: or D:: CD X:\OS2\BOOT COPY IBM1S506.ADD IBM1S506.ADDBKUP ERASE IBM1S506.ADD COPY A:\DANIS506.ADD IBM1S506.ADD EXIT now you may reboot your machine to pick up on the second phase of the OS/2 installation because your updated driver is active and NOT the old one from your CDROM media during your installation phase. Of course, I am assuming that you only need one driver; but if there are more, perform a similar procedure as above.
Note that even if Danis506.add is there BUT not referenced in your OS/2 CONFIG.SYS, you will still be rebooting with your old IBM1S506.ADD since that driver is what CONFIG.SYS will be referencing. It is best practice to rename the DANIS506.ADD to IBM1S506.ADD because even if your second installation phase is successful, the third one relating to networking installation will fail.
You may custom update your installation media subsequently with UpdateCD < http://xenia.sote.hu/~kadzsol/rexx/sajat/updcd.htm > UpdateCD appears somewhat complex --hence familiarize yourself with the instructions; notwithstanding, even if you only update the single Danis506.add, your new bootable UpdateCD media will beat your existing one --at least for your laptop. |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 15 Feb, 2007 on 10:35 |
| dljone9 Do you mean I should create a C and D volume, or just the D ? |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 15 Feb, 2007 on 10:48 |
| El Vato >Like in the "old" days, if you are creating a boot update diskette set I'm not, I'm booting directly from the eCs CD, in eCs 1.2 I can create a diskette with the label "BOOT_UPDATE" or a text file called "BOOT_UPD.TXT" then everything from this disk will be copied into the os2\boot directory as part of the installation process. eCs uses the Danis506 driver as default, so the config.sys is correct, and the latest driver is located in the os2\boot directory. >...and the utility is correct because the driver that did not At the time of the boot manager, all disk access should be via the bios, as no form for drivers has been loaded yet ! If the driver was missing, the boot process should start, and the infamous "The operating system cannot operate your harddisk" message should show. But thanks for your input. |
| Subject | : | Re:eCs installation problems |
| Author | : | dljone9 dljone9@os2world.com |
| Date | : | 15 Feb, 2007 on 22:28 |
Just create a D: - with this new LVM, you can assign drive letters as I would create a C: though, who knows - you may want to install |
| Subject | : | Re:eCs installation problems |
| Author | : | El Vato |
| Date | : | 16 Feb, 2007 on 08:19 |
Evidently, that is only an assumption --as there is an indication to the operating system to boot from the installable partition during the second phase of the installation, i.e., the target that you can not set as installable. You might even have an preexisting WinXX partition table that does not allow you to set your partition installable. Those are extremely hard to remove with LVM (if at all). You have to use either its creator WinXX or a bootable Linux CD to do so. Pressing F5 when inside the LVM utility will give you some insight on the physical partitions existent in your hard disk. It will also tell you which partitions are Primary and which are Logical, which are Available and which are "In Use."
I mentioned "referenced" not "missing"...i.e., if the driver was downleveled to the original one that did not "see" your hard disk, you would not necessarily have that infamousity across your dark screeen. Anyhow, hope that dljone9's recommendation brings you success to your endeavor as there appears to be several possible target entities in your hard disk. |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 28 Feb, 2007 on 10:50 |
| >I would create a C: though, who knows - you may want to install >another OS or use it as a file partition or who knows... I now have tried to create a d: drive with and without a c: drive, with the same result I'm rather busy rebuilding my house right now, so (for now) I have installed ubuntu, but will try again later. Kim |
| Subject | : | Re:eCs installation problems |
| Author | : | kif kim@foder.dk |
| Date | : | 28 Feb, 2007 on 11:30 |
Yes and no. In my experience, drivers are loaded after the OS/2 or eCs splash screen is shown, and in this case I do not get anything !
All existing partitions was removed, using the installed XP when I got the laptop, afterwards I have deleted and created countless partitions using ubuntu and eCs. When I start I delete every partition (F5 in LVM shows me an empty disk), install bootmanager, create a logical partition of up to 2 GB, and try to install on that one. I have tried to create a primary, and install eCs without a boot manager, then i get a message telling me the BIOS could not find an operating system !
Yes, but the driver isn't downleveled, it's the latest one, size date and time is the one from the floppy ! Thanks for your input, when I get some spare time, I will try again, and post my results here. Kim |
| Subject | : | Re:eCs installation problems |
| Author | : | Andi |
| Date | : | 28 Feb, 2007 on 12:45 |
| Is there a BIOS option for SATA? I had to set such option to 'compatibility' when installing eCS on a Thinkpad. |
| Subject | : | Re:eCs installation problems |
| Author | : | tex |
| Date | : | 01 Mar, 2007 on 03:28 |
DavidG |