| LinkSys WPC-11 v4 problem |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
1. LinkSys WPC-11 v4 problem |
|
|
| Well, trying to set up a LinkSys WPC-11 v4 card and so far I haven't managed to establish any uplink to the router (to be mentioned is that I verified on a WinXP system that the card works with and without WEP-encryption). On the OS2 system I've stripped of so only tcp/ip is used and nothing else. The driver is loaded and I've tried out with two version of the driver for LinkSys, the LinkSys WPC-11 V.3 NDIS driver from October 2003 and the Generic PRISM RC4, Linksys WPC11 v3 Beta. Both loads without any problem, but still no link. Also I've set the channel no, SSID, etc within MPTS. So I'm really open for suggestions here from thoose of you that have tested and currently running with either of the drivers. /Kim |
| Date: 14 Apr, 2004 on 14:33 |
|
|
Normal member in user
       posts: 28 since: 21 Feb, 2001 |
|
2. Re:LinkSys WPC-11 v4 problem |
|
|
| Hi, Are you sure that your pccard socket driver is working correctly as well? I've had a bit of a difficulty finding a good working driver for my TP R40.
Luc Van Bogaert
|
| Date: 15 Apr, 2004 on 09:01 |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
3. Re:LinkSys WPC-11 v4 problem |
|
|
| Starting to think that the errors might be there; what version are you using? |
| Date: 15 Apr, 2004 on 12:08 |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
4. Re:LinkSys WPC-11 v4 problem |
|
|
| Well, when using IBM sockets service the system boots up without any problem, etc. Then tried Danielas patched socket service without any luck since it's skipped during boot. But then again the TI4510 chip is not on the list. So my question is now if the APSoft's Socket Services for OS/2 might be a solution? |
| Date: 15 Apr, 2004 on 20:17 |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
5. Re:LinkSys WPC-11 v4 problem |
|
|
| Well, it seems that APSoft socket service seems to support huge amount of chipsets including the TI4510 used within the Dell Inspiron 8600 that I'm using. For others with the same problem, check following pdf document of supported chipset. |
| Date: 15 Apr, 2004 on 20:46 |
|
|
Normal member in user
       posts: 28 since: 21 Feb, 2001 |
|
6. Re:LinkSys WPC-11 v4 problem |
|
|
I would also suggest you contact Daniela Engert and ask her about the support in her patched driver for your chipset. I know she uses a Dell laptop, and that's why she patched IBM's driver in the first place. She might still have a newer, unreleased version of her driver available. I know, 'cause she helped me out this way as well for my Thinkpad R40.
Luc Van Bogaert
|
| Date: 16 Apr, 2004 on 00:33 |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
7. Re:LinkSys WPC-11 v4 problem |
|
|
| I sent here her an email yesterday and as you mentioned, in her readme files she mention that she is using Dell laptops. Lets see what comes out of it. |
| Date: 16 Apr, 2004 on 06:48 |
|
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
 |
8. Re:LinkSys WPC-11 v4 problem |
|
|
last updated at 17 Apr, 2004 12:27 (1 times) I got an updated version of ss2ticb that have been updated with a number of chipset including the TI4510. When booting the system the driver loads and halts the system. but the card is now powered so I'm getting a half step closer to the goal. The earlier version of the driver did not load and was just skipped during boot.Also if there is no nic inserted it boots up without any problem. /Kim |
|
Team member in staff
       posts: 2128 since: 10 Dec, 2000
 |
|
9. Re:LinkSys WPC-11 v4 problem |
|
|
| Well, played around a bit more, but there isn't much to do regarding parameters when it comes to IBMs socket service. I remark out cardbus tools since it's not needed just to make sure. BASEDEV=PCMCIA.SYS BASEDEV=IBM2SS14.SYS rem BASEDEV=SS2TICB.SYS BASEDEV=AUTODRV2.SYS rem DEVICE=C:\TOOLS\CARDBUS\VPCMCIA.SYS rem DEVICE=C:\TOOLS\CARDBUS\PCMSSDIF.SYS rem DEVICE=C:\TOOLS\CARDBUS\PCM2SRAM.SYS rme DEVICE=C:\TOOLS\CARDBUS\FLSH2MTD.SYS rem DEVICE=C:\TOOLS\CARDBUS\PCM2FLSH.SYS BASEDEV=PCM2ATA.ADD /S:1 /!DM /NOBEEP BASEDEV=OS2PCARD.DMD DEVICE=C:\OS2\$ICPMOS2.SYS /G DEVICE=C:\IBMCOM\MACS\GENPRISM.OS2 Question regarding parameter /G on the ICPMOS2.SYS what does it do? There is no mention about within the cardbus documentation. I've also tried to change the number of cardbuses from 2 to 1 on PCM2ATA.ADD. But, so far no difference. If I boot the system without the LinkSys card it loads Danielas driver without any problem. Might be a tiny clue for something wierd.. |
| Date: 17 Apr, 2004 on 14:26 |
|
|
| LinkSys WPC-11 v4 problem |
|
|
| All times are CET+1. |
< Prev. | P. 1 | Next > |
|